Samsung SH12ZSG горят все индикаторы.
Главная  |  О сайте  |  Реклама  |  Помощь   
Интернет-Сообщество Профессионалов Рынка Климатической Техники Aircon.Ru
  .: Мой Aircon   .: Технические ресурсы   .: Обучение и карьера   .: Полезные ресурсы   .: Об'явления   .: Форум   .: Новости
Авторизация
Запомнить меня на этом компьютере
Забыли пароль?
Регистрация

  инструкции
  технические каталоги
  Cервис-мануалы
  стандарты и СНиПы
  программное обеспечение

  вакансии
  семинары
  резюме
  книжная полка

  статьи производителей
  наши пишут
  журналы и издания
  файлы
  Выставка "Мир Климата"
  расшифровка моделей

  поиск оборудования (29)
  поиск зип
  поиск информации (5)
  спец.предложения

 
  Новости производителей
  События российского рынка
  Лента новостей
  Специальные предложения!
  Разместить баннер на своих условиях


Официальный дистрибутор TICA - ТРЕЙД ГРУПП

 Главная Форум Ремонт оборудования и запчасти Samsung SH12ZSG горят все индикаторы.

Поиск по сайту


.: Форум AIRCON.RU – Тема «Samsung SH12ZSG горят все индикаторы.»

Форумы
Список тем
Новые темы
Поиск
Правила
Помощь
Авторизация: 

АБХМ (Абсорбционные холодильные машины Ebara)
  Просмотров: 6391Тема: «Samsung SH12ZSG горят все индикаторы.» в форуме: Ремонт оборудования и запчасти
#1
На комнатном блоке кондиционера Samsung SH12ZSG горят все индикаторы. На пульт реагирует звуковым сигналом один раз после включения в сеть. Может быть сбился конфигурационный код в EEPROM? Подскажите как ввести код для этой модели.
Какие еще есть мысли по поводу описаной выше неисправности.
Профиль
E-Mail
#2
Да вроде в pdf-е написано:

Option error(option wasn’t set up or option data error)

Set up the Model Option
MODEL___OPTION CODE
SH12ZSG__066025-172362
SH09ZS8__027064-17221d
SH07ZS8__026064-1720Fb

8-5. Set up the Model Option
Step 1 : Preparing the remocon to main PBA option set
1st Remove the battery from the remocon.
2nd Press the temperature raise/down button simultaneously and insert the battery again.
3rd Make sure the remocon display shown as 00 00 00

Step 2 : Second stage preparation of the remocon option set.
. Note ; In case the wrong letter has been selected, continue to press the button until the correct letter appears.

1st If the first stage number “0” appears on the display, proceed to the second stage.
2nd Every time the "1" and "7" button, “0 ” and “1 ” each continue to appear.
3rd Whenever pressing the 2, 3, 4, 5, 6, 8, 9 , 10 , 11, 12 button, the number increases from
0~9(0123456789) and A, b, C, d, E, F each time.

1 If the first number is 0 , it is correct otherwise press "Mode" until 0 appear.
2 When pressing the "UP" button 0 ~ F appear on the display,select one of them.
3 When pressing the "DOUN" button 0 ~ F appear on the display,select one of them.
4 When pressing the "FAN" button 0 ~ F appear on the display,select one of them.
5 When pressing the "Off Timer"button0 ~ F appear on the display,select one of them.
6 When pressing the "ON/OFF"button 0 ~ F appear on the display,select one of them.

1 If the first number is 1, it is correct otherwise press "Mode" until 1 appear.
2 When pressing the "UP" button 0 ~ F appear on the display, select one of them.
3 When pressing the "DOUN" button 0 ~ F appear on the display, select one of them.
4 When pressing the "FAN" button 0 ~ F appear on the display, select one of them.
5 When pressing the "Off Timer" button 0 ~ F appear on the display, select one of them.
6 When pressing the "ON/OFF" button 0 ~ F appear on the display, select one of them.

Step 3 : Reconfirming option set after completion (in case of ex. 066025-172362)
After pressing "Mode" selector for the 0 mode, the display shown as 066025.
After pressing "Mode" selector for the 1 mode, the display shown as 172362.

Step 4 : Pressing the ON/OFF button
When pressing the operation ON/OFF key with the direction of remote controller for unit, the sound “Ding” or “Diriring” is
heard and the OPERATION LED lamp is flickering at the same time, then the input of option is completed.
(If the diriring sound isn’t heard, try again pressing the ON/OFF button.)

Step 5 : Unit operation test-run
First, Remove the battery from the remote controller.
Second, Re-insert the battery into the remote controller.
Third, Press ON/OFF key with the direction of remote controller for set.

Error Mode :
1st If all lamps of indoor unit are flickering, Plug out and plug in again and pressing ON/OFF key to retry.
2nd If the unit is not working properly or all lamps are continuously flickering after setting the option code, see
if the correct option code is set up for it’s model.



новое-это давно забытое старое
Профиль
E-Mail
#3
Спасибо за информацию. Очень помогли. О результатах напишу.
Профиль
E-Mail

Читают тему
гостей: 1, пользователей: 0, из них скрытых: 0
   

 





Copyright © 2001-2007 Aircon.Ru, если иное не указано дополнительно.
Администрация сервера не несет ответственности за достоверность
и корректность информации, размещаемой пользователями сервисов.